Just throwing this out there for the 2.5g nanos

Why buy when you can DIY?
Post Reply
snickle
Posts: 58
Joined: Mon Apr 09, 2007 9:44 am

Post by snickle »

Dave,

I am probably in. What time and where?

I did not see a final list of the wood needed.

Steve
ingg
Posts: 2418
Joined: Fri Feb 16, 2007 1:29 am

Post by ingg »

My address is 2002 Kings Forest Trail, Mt Airy, MD, 21771. It may not mapquest as it is new construction, just do king's forest if it doesn't see our address yet.

From VA, two ways:

Beltway up 270 to 27 (Father Hurley Boulevard).

North on 27, through Damascus, cross under 70, into Mt Airy.

Or, 15 North to Frederick, then 70 East. (This'd be faster for Ghanzafar I know.)

(From Baltimore, 70 west to 27 North, then follow directions below.)

Third light after crossing under/exitting 70 should be Watersville Road.

Right on Watersville, third road on the right is Locksley Lane. Big sign says Nottingham.

Right onto Locksley.

Second right onto Kings Forest.

Follow it down, when you see a cross street coming into Kings Forest, that cross street is opposite my driveway. Silver Avalon will be in the driveway.


Home is 301-829-6117, cell is 443-844-4788.


Steve,

I'll get us the wood, easier to just grab it in lump amount. We're using the poplar I showed at the last meeting. Should be about $16 and change of wood.

I'll need a final list of folks/amounts the day before, to gather our supplies...

Tentatively Saturday May 12th, others coming from Virginia, so... say 10:30? That work for Neilan and Ghanzafar?

We should have them built by the afternoon.
Dave
snickle
Posts: 58
Joined: Mon Apr 09, 2007 9:44 am

Post by snickle »

We still on for this?
ingg
Posts: 2418
Joined: Fri Feb 16, 2007 1:29 am

Post by ingg »

Yes as far as I know.

Neilanh, Ghanzafar, you guys are okay with date/time, yes?
Dave
User avatar
Ghazanfar Ghori
Site Admin
Posts: 3258
Joined: Sun Nov 23, 2003 5:26 am
Location: United States

Post by Ghazanfar Ghori »

Actually - Ive got to attend a CCA/PVAS/GWAPA meeting pre CCA.
If you guys don't mind me showing up a little late - I can make it.
User avatar
neilanh
Posts: 436
Joined: Sat Feb 24, 2007 11:00 pm
Location: Sterling, VA

Post by neilanh »

I got the kitchen pass.

Ghaz, how much is a little late? Any time on saturday is okay with me.
ingg
Posts: 2418
Joined: Fri Feb 16, 2007 1:29 am

Post by ingg »

Little late is s'okay by me. We'll probably have the sides cut and ready for you.
Dave
User avatar
neilanh
Posts: 436
Joined: Sat Feb 24, 2007 11:00 pm
Location: Sterling, VA

Post by neilanh »

Well I was just thinking we could adjust the time for Ghaz since its just he and I. Like I said, I'm good for anytime. If you're going to go ahead and start that morning, I'll plan on being there 10:30-11ish, and Ghaz can show whenever he can.

Any good LFSs right near you? I don't venture up that way often.
User avatar
Ghazanfar Ghori
Site Admin
Posts: 3258
Joined: Sun Nov 23, 2003 5:26 am
Location: United States

Post by Ghazanfar Ghori »

Ive got to be at the CCA meet at 11:00 AM - off of Georiga Ave. Should be
done there within the hour and I can probably be up at your place 12:30ish
give or take 15 minutes.
snickle
Posts: 58
Joined: Mon Apr 09, 2007 9:44 am

Post by snickle »

A little later is fine by me. Just let me know.
Post Reply

Sponsors